Find App Bitumen Waterproofing Membrane, App Modified Bitumen Membrane, App Asphlat Roofing Membrane on Industry Directory, Reliable Manufacturer/Supplier/Factory from China.

Inquiry Basket (0)
Home > Products > Modified Bitumen Waterproofing Membrane > APP Modified Bitumen Membrane > CHOICE-LINK APP outdoor waterproof rubber flooring membrane

CHOICE-LINK APP outdoor waterproof rubber flooring membrane

Basic Info

Model No.: CLA

Product Description

CHOICE-LINK APP outdoor waterproof rubber flooring membrane   Description: CHOICE-LINK APP outdoor waterproof rubber flooring membrane is made of modified bitumen through scientific process with heat transfer oil as carrier. It has such advantages as no flow under high temperature condition, being soft under low temperature condition, being high flexible and aging resistant. Thus the flex durability, flexibility and cohesive force of the asphalt is largely improved. Therefore, the waterproof quality of the buildings improves a lot and service time also prolongs.    Specifications: 1. Type: Type I, Type II 2. Base felt: PY/S/Composite felt 3. Upper surface material: PE/Sand/Mineral 4. Thickness: 2mm-5mm or according to customer’s requirement   Usage: CHOICE-LINK APP outdoor waterproof rubber flooring membrane can be widely used for building surface and basement waterproof in industrial and civil engineering, as well as waterproof for subway, cold storage, airport runway and viaduct.   CHOICE-LINK APP outdoor waterproof rubber flooring membrane is specially suitable to the architecture’s waterproofing in cold area and to the building of unstable constructions, while APP specially is suitable to areas of high temperature and of strong sunshine.   Application areas: 1. Balcony, bathroom, kitchen 2. Tunnels, Industrial roofs 3. Flat and sloped roofs 4. Basements, Foundation and retaining walls 5. Gardens, Bridges   Technical Data  

NO.

Reinforcement

PY

G

Type

I

II

I

II

1

Soluble

Matters

2mm

-

1300g/m2

3mm

2100g/m2

4mm

2900g/m2

2

Water tightness,30min,≥Mpa

0.3

0.2

0.3

3

Heat resistance degree,°C,no glide, no flow, no drop

90

105

90

105

4

Tension,

N/50mm

Longitudinal

450

800

350

500

transverse

250

300

5

Elongation at break,≥

Longitudinal

30%

40%

-

transverse

6

Brittleness point

-18°C

-25°C

-18°C

-25°C

7

Tearing strength,≥

Longitudinal

250N

350N

250N

350N

transverse

170N

200N

8

Manual work and climate quicken aging

Appearance

No.1 degree

(no glide, no flow, no drop)

Longitudinal tensionkeeping

rate,≥

80

Brittleness point

-10°C

-20°C

-10°C

-20°C

GB18242-2000

                   
    Features and advantages: 1. High impermeability, high tensile strength, high extension coefficient 2. Puncture resistance, tear resistance, anti-corrosion, mildew resistance 3. SBS is suitable for lower temperature area, while APP is suitable for higher temperature area 4. Perfect durability, service life can up to 30 years 5. Flexible install method: Either by heating and melting method, or cold-adhesive method. Either single or multiple layer. 6. No flow, no dripping in higher temperature;     No crack in lower temperature   Construction Requirements Basement Treatment: The waterproofing base should be strong smooth, and clean without particles on the surface. No peeling or cracking shall exist on the surface. The corners of the base shall be made into arcs with a radius of no less than 20mm or triangular. The drain slope, division seam, and air vent shall be carried out and treated according to design requirements. Then brush promer on the foundation until it is dry.     Installation: 1) Make sure the roof deck smooth, clean and dry (Moisture <9%), then coat the surface of your roof deck with a kind of bitumen paint till dry to start installation.   2) Two ways in installation: First, heating and melting method----Heat the PE film of the membrane and roof deck surface by heating and melting method to nearly melted (not flowing), then install the membrane fully bonded to the roof deck with overlaps of 5-10cm.   Second, cold-adhesive method-----Pour the cold adhesive homogeneously on the roof deck, the roll the membrane to install it to be fully stick to roof deck.   3)  After installation, a full serious inspection is required to make sure no air bubble, no fold, no falling away to guarantee the waterproof life.     Package, transportation and storage: 1. Packed by plastic bag or adhesive tape. 2. During transportation and storage, keep the package well , put them in a dry airy place, keep away from direct sunlight, acids, alkalis, oil and organic solvents. 3. The shelf life is 12 months under normal storage and transportation conditions. After that period, the product can still be used if it complies with all the items in the specification.   Contact Us 1, Honest supplier to the worldwide buyers 2, Factory, direct supplier, competitive price 3, Know how to control the costing with 10 years producing experience 4, Warm and friendly service and guide 5, 3 shifts workers for 24hrs production, high capacity 6, Small and big orders are welcome from the worldwide 7, 24 hours service for you 
   

Contact us if you need more details on Outdoor Waterproof Rubber Flooring Membrane. We are ready to answer your questions on packaging, logistics, certification or any other aspects about App Outdoor Waterproof Membrane、Rubber Flooring Membrane. If these products fail to match your need, please contact us and we would like to provide relevant information.

Product Categories : Modified Bitumen Waterproofing Membrane > APP Modified Bitumen Membrane

Email to this supplier
  • *Subject:
  • To:

  • *Messages:
    Your message must be between 20-8000 characters